Search results

I found this page with a bunch of pictures of SCSI to Ethernet solutions from a few providers: https://applerescueofdenver.com/products-page/networking/networking-cables-amp-adapters/scsi-to-ethernet-adapters-external/ Every one of them has an external power adapter plug. And I think this may...

April 13, 2024 Board Meeting Attendance: Kai Robinson, fogWraith (Christian), Jacob (Androda), Justin (jdmcs) Absent: Josh (Drake), Eric (eric), Bruce (Branchus) Agenda: Item 1: Governance Policies Notes: Board Governance Policies have been agreed upon and now they need to be presented to...

Yes indeed. The PowerBook 100 is a miniaturized Mac Portable with a few improvements in the power management circuitry. Lead acid primary battery for the win.

Anyone have the TRG Xtra Xtra (or Pro) upgrade, or any other RAM / flash upgrade boards for Palm Pilots? You may be able to guess where I'm going with this question.

I enjoyed Palm Pilots. Had the Fossil Abacus Wrist PDA watch, which honestly was mostly useless but still random and fun.

Although the M5120 and M5126 are different, I believe the connections between Power Manager chip and VIA are the same. Check that all the data bits and PMACK/PMREQ traces are solid using the available Portable schematics. The power manager chip itself also needs a good 5v supply, which the...

The /AS line is used to determine whether the RAM upgrade card should be "selected" for use by the system. Removing that jumper "floats" the /AS input so depending on your local electromagnetic interference it might disable the RAM card. Or it might cause problems if sometimes the card thinks...

I did not, because of the answer to question #3. Correct, the main 5.2v rail is required for PRAM value retention. I do not recommend storing the Portable for any long-term period of time with a 9v battery installed. And thus have decided simply not to support the installation of 9v PRAM...

Two resistors are required. One end of the resistor connects to the point on the Pico header as shown. The other end of the resistor may connect to either of the specified points on the left of C13 or C9.

Well done. Now hopefully the copper doesn't oxidize over time and break contact.

Got any pictures of the melted section? Depending on which cable was melted we might be able to recreate it. Though if I'm understanding correctly, this is the interface to the resistive touch sensor area - and I believe that's hard-connected to the panel.

As I just discovered this morning, the Exabyte 8505 tape drive (and likely others in this series such as 8500, 8200, 8205, 8700, 8705) are affected by the leaky SMD capacitor plague. These drives have a vertically mounted power converter section which naturally has leaky capacitors dumping...

That depends entirely on whether the external 5v video power line is disabled when the Portable is in sleep mode. I would have to check. It's a switched supply, so if power is cut to the external video pin in sleep mode then it would be safe to remove. Note that the external video port has a...

Stock counts are low on the Mac Portable VGA adapter, but more will be on the way soon. This product does what it says: Mac Portable digital video out port -> 640x480 VGA. Doesn't convert the other way, sorry. https://androda.work/product/vga-adapter-for-macintosh-portable/

Normally the main power rail is intended to be at 5.2v. But I've seen these systems at 5.15v, 5.26v, etc. The hybrid module's feedback resistors are, I believe, mostly 1% or 0.5% tolerance. 5.3v is 1.9% different than 5.2v, and not likely to be an issue. But it does show a little drifting...

Generally speaking it's safe to connect or disconnect things from the motherboard when the main 5v rail drops to a solid zero volts. My listing states to wait awhile because these are supercapacitors and if you accidentally bump the legs with something conductive you're going to get a huge...

I've done a schematic diff between older and newer BlueSCSI versions to remind myself what the issue was, and wrote a section on the BlueSCSI V2 Wiki on the subject: https://github.com/BlueSCSI/BlueSCSI-v2/wiki/Hardware#hardware-tweaks--fixes The issue was pull resistors, and the instructions...

A Backlit Portable as shipped by Apple is capable of addressing up to 8 MB of RAM. There is one megabyte on the motherboard, and my RAM card design provides an additional 7. But the Backlit Portable will only see 4MB of that 7 when in the RAM slot, because Apple changed the RAM decode logic...

March 2, 2024 Board Meeting Attendance: Jacob (Androda), Justin (jdmcs), Kai Robinson, Bruce (Branchus) Absent: Josh (Drake), Ron (Ron’s Computer Videos), Christian (fogWraith), Eric (eric) Agenda: Item 1: Governance Documents Action Items: Androda to recompile all the notes and edits...

There are two issues present which were causing the "wake from sleep" problems. First, the Pi Foundation decided to make all IO pins on the RP2040 default to "pull down" mode. This means that instead of simply "floating" (not changing the electrical state of their connections), they actively...