Search results

I recently remodeled my garage where I restore vintage Macs. The outlet circuits are GCFI at the panel by code. they’ve mostly worked fine but yesterday I plugged in a Lisa which works fine on other circuits but trips the new circuits in the garage immediately. I’m guessing this is because the...

I can't find my notes for that one, but here's what I replaced it with. But I can't recall if it's 68pF (probably?) or uF or what voltage it's rated for. Sorry.

That was my thread :) The black cylinders are indeed choke inductors and 10uH worked fine for me. From my restoration notes: 8x .001 uF 50v ceramic disc, +15% 85C Can you point it out in a photo?

The body of your post is pretty confusing to me but the bottom line is that SE/30 only supports up to System 7.5.5. Perhaps there are hacks to get 7.6 working (it needs 32 but clean) but I can’t imagine 8 would run on one since it requires an 040 or better.

Small update just so I don't forget. I got the signal looking much better with light backgrounds by connecting pin 2 of the 16-pin header header to pin 8 VGA (blue return). The remaining interference is more apparent with darker backgrounds. A ferrite shield on the cable did not help. I'm...

That's the header I used for the card I got working. I moved my adapter over to that header on the 2nd card but it does not work and the pins look very different on the scope as per my last post. The scope shots seem to indicate the FPGA isn't being driven correctly with the driver that's...

I tried swapping in the second card with the three headers, but I did not get video from it. It uses the same Xilinx FPGA and mostly looks similar apart from the extra header, but the scope shots look quite different. Perhaps this one requires different drivers. I'm attaching the scope shots as...

For now I had to share at least one photo of it working on its own. :)

I think I got it pretty much sorted through trial and error. If anyone can shed light on why this config works, please let me know. The table below is the working setup. There's still some tearing, but I think that's a shielding issue I'll tinker with later. Many thanks to @Trash80toG4 and the...

I probed all of the ECL header pins but couldn't make good sense of them. From experimentation, I mapped the following so far. When connecting any of the pins marked 'Video' to any of the VGA color channels I get a very dark and noisy image. When connecting pin 2 I get an inverted dark and...

@Trash80toG4 I might not understand your questions but I posted the connectors I’m using in the previous post which included photos. Another post established that there’s a header for TTL (the one I’m using) and a smaller one presumably for ECL. I got the scaler at the suggestion of someone else...

Yay it's actually doing something!! This is with the following setup IDC Pin VGA Pin (Female) 1 5 (HSYNC Ground. Not necessary, but improves clarity.) 3 6 (Red return. Not necessary, but improves clarity.) 9 14 (VSYNC) 11 13 (HSYNC) 13 1, 2 and 3 (Video signal) combined to get B&W...

I made a new 16-pin IDC cable to connect to the video card's header and ordered a HD-15 terminal breakout connector to make trial and error a bit easier.

After checking the pinouts again the problem seems pretty clear. At the very least HSYNC and VSYNC are on the wrong pins. Next I'll jumper HSYNC and VSYNC to the right VGA pins and start experimenting to find the right pin for video.

I hooked up the regular SE analog board and CRT to the micromac MLB. Found some bad ram and that the BlueSCSI image had no driver. I installed the Lapis Dual Screen Software 2.E control panel I had the most success with previously on System 7.1. I did see some brief distortion on the Extron...

It is, it just also has a pass through PDS slot which may be hard to make sense of in the photo. I can definitely hack some jumpers together to make the wiring simpler. Will put some more energy into it soon. Thanks for the info!

I got the Extron RGB-HDMI scaler. The box itself is outputting video. I have it routing to an Elgato HD60+ connected to a MacBook Pro. The MicroMac Lapis card is connected to a DB-9 to HD-15 adapter which is connected to a regular VGA cable which is connected to the Extron. The status...

Sweet, thanks!

While I wait for the power adapter to arrive, I’ve been reading through the manual. I see it scales to a bunch of different resolutions for output, but should it be capable of dealing with 64x870 input? If it’s connected to a normal TV or monitor, would the picture just have two huge black bars...

Did you set the nub on the large gear towards the front of the drive when you put it back together?