Search results

While I was in here, this is the SE Mainboard with the accelerated on top with the plugin for the video card.

Was observing today; on startup both screens light to the grey typical back ground, then the Radius accelerator badge on external screen then the full page display page badge on external screen then the mac smiley face on the SE internal screen. After boot, then menu is at the top of the...

Check the ROM version for sure; it’s a real knuckle buster to get these out but probably possible to read and burn; pretty sure when mine boots, both screens are on

Just adding these for possible informational purposes for any cloners out there. All photos are the same system/card.

have the 7100 cache......in US though

I’ll see if I can find it…..maybe a little wait, either in storage container or taped to the working one inside the machine

installed photoshop 2....i cannot find a full screen option; the viewable diagonal on finder is 9 and 7/8 inches. heigh 5 and 2/8ths; width 8 and 4/8ths; inclusive of menu bar.

All of the above are measurements with the on screen ruler just with different units using SuperPaint 1.1, I cannot find any command for full screen as per your Photoshop description; good news though, found a photoshop 3.0 that should install, but on CD so now will need to find cable and...

How about this....in the Superpaint 1.1 available window I can see, the ruler when set to "screen dots" is 575 horizontal and and about 19.5 cm when ruler set to cm, 7 and 11/16 inches and 47 when set to "pica/points" Vertically 720 when set to "screen dots", 24.4 cm, 9 and 5/8 inches or 57.5...

Well; on 170 have Superpaint 1.1, MacDraw and MacPaint if there is a way to obtain the information there. Superpaint 1.1 does have an option to measure in "screen dots" but no option for full screen. . Will see if I have disks somewhere to see if I can install photoshop.

It was just the video card, switch out some faceplates cards etc and found a working AGP ATI 3d with no glitches

I've got you on this....I have 3 Powerbook 180c; multiple years ago entered rabbit hole Powerbook 180c 1 boots OK but the screen has a line right through the middle of it so the LCD caps have probably dissolved something or at lear need replacement Powerbook 180c 2 is in pieces but worked...

There is a persistent graphics glitch on on recently obtained Cube. Attached are pictures with the computer booted and the other is the pattern on the screen between shutdown and complete power off, i just thought it showed the pattern the best. The glitch to the right of the mouse moves with...

A little tangent; in about 2015 or 16 I found a local auction and picked up 2two SE/30's and a plus for about 60 bucks. It was my introduction to the existence retro/mod/support community out there. I found a thread on the other site with instructions of how to put a Radius II SI card into an...

Here's a picture of one side of a full page Radius I have in an SE; looks similar to above but if you see anything that could be helpful I could disassemble and be more specific.

If anyone is interested in a non working 7100 cache with its AV9170 shorted to ground, I’ll send it.

Thanks. So it looks like that on chip VDD is shorted to ground. I found another cache and it works fine.

How did it go?

I have a C2N Datasette that will not load tapes. I've looked at the schematics, have put an oscilloscope on the read heads, watched several repair videos/tuning instructions. I also have a working SD2IEC. Why do I care if the C2N Datasette works or not?

Just checking for grounds on the caps and IC's, the small IC in the center on the backside picture has pins 5 and 7 to ground....cannot find a data sheet on it though....the numbers are AV70-1 then 9508 on the IC itself...?anyone know what specifically I should search for to find a data sheet...