Hacking the Kodak Reels 8mm Film Digitizer (New Thread)

[milek7]

Looks like my EU supposedly-typeD scanner doesn't work with any of the type D firmware posted here, including stock. It shows this for like 5 seconds after hitting "Record" and then goes back to preview.

 

[Mike Damore]

My serial number is J2925148BK01666. I flashed FWDV280-2 (after removing the "-2") without any issues. Seems these new numbers are D's.

Now I need to figure out how to changes the values...

Thanks , melw!

 

[FrenchNum]

Absolutely I'll share it on here as soon as I've got it off the scanner.

I'm doing at least one pass of all the films I have (now about 3/4 of the way through) before I crack this thing open, in case I manage to completely munt it. They're pretty pricey here in Aus so it's not something I want to tackle without getting mum's films all done at least as well as the crappy stock firmware can manage.

I've stepped up my scanning schedule a bit, and knocked out about 10 reels today.

Hi ArgieBargie,

I hope your film scanning is going well. I just wanted to follow up regarding the original firmware dump from your A3026 unit.
My return window is now getting quite close, so I need to decide soon whether to return my scanner or attempt another recovery method.
Have you had a chance to extract the firmware yet, or do you have an approximate idea of when you might be able to do it?
I completely understand that you need to finish your family films first, and I do not want to pressure you. I just need to know whether the dump is likely to be available before my return deadline.
Thank you again for offering to share it.

 

[meggatron]

Still curious if anyone else has a 100% confirmation on this stock number firmware version to use: J2925148BK00696

The J prefix seems extremely rare at this point, I havent seen anyone else mention having one with that prefix.

Did you end up trying out the D version? Just ordered a unit off Amazon, similar serial number: J2925148BK01099. From what I can tell it's probably a D but it hasn't been tested yet.

 

[melw]

Posting a new Type D build for anyone who wants to try it. Same base as the last one, two main changes:

• Manual white balance. While recording, use the arrows to pick R/G/B and +/- to adjust (±16 coarse, left/right for ±1 fine). The setting is saved and restored automatically after a power cycle. Use RST to reset back default values.
• Card-stall now stops the reel. If the SD card can't keep up and the recording stalls, you still get the on-screen CARD SLOW / REC STALLED warning — and now the motor also stops, leaving the frame counter frozen on the last good frame so you can see exactly where it cut out instead of finding out at the end.

Also cleaned up a false "REC STALLED" that used to flash in preview after a normal stop.

Reminder: for the higher bitrate, use a FAT32 card, 32 GB or smaller, Class 10 / V10+. Big exFAT cards write too slowly and will truncate long reels.

 

[melw]

Quick update on an issue I've seen using post #616 "D" version drop on an H2825 unit. It has happened twice now so I thought it might be useful to share.

The first time it happened at about 1900 frames into a 50 foot roll of Super 8 (~3600 frames total/roll). The display froze at that frame but the film kept advancing and appeared to keep capturing. I assumed it was just a glitch so I stopped the unit and restarted. I completed about six or eight rolls before it happened again.

The second time was again with a 50 foot roll and it froze at about 2400 frames in, same behavior. I paid closer attention this time and waited for the end of the roll to move through, not knowing if it was still capturing. At the end of the roll, the OK button and power button were not responsive, and I had to unplug the unit to stop the motor. The SD card did not have a file for the capture. I was using the same 128GB FAT32 formatted SD card that I had been using successfully.

Not knowing the cause, I've reverted to the post #605 firmware and went back to the 16GB FAT32 card.

So far, so good but @melw let me know if there is anything you'd like me to do to troubleshoot or try to replicate.

Sorry for slow response - been on the road and just today got back to this. I'm tempted to try also the large SD card + FAT32 combo - large cards with exFAT are not working well, and 32GB FAT32 should work without issues. I just shared an updated Type D build (#645) that has improved stall detection + support for stopping motor when recording frame counter no longer advances.

I can feel the pain of not getting 50 foot roll recorded and only finding out at the very end. While I can't say for sure whether it's the large SD card, I'd lean toward using the 32GB one, if it's large enough to hold the recording, just to be on the safe side. Even with improved record stall detection, it's not nice if the recording cuts in the middle.

 

[UKAussi]

New purchase of this to scan my mother-in-laws huge stash of 8mm/Super 8mm films nobody has seen so volunteered as a tech guru to do this in house as she has almost 100 films!!
Being a tech geek for 30+ years I figured I would "tweak" this as stock was not great and hate devices that dont use all their capabilities.

M2025148BK*****

Suffice to say the B and C did not work for my device as either froze screen or inverted+color warped + froze screen

I used the D from above in #645 and it is back to working and scanning again so can start on this "stack" of up to 50 year old reels! (wife is just a toddler)
Using a 64GB PNY card (100MB/s - V30) reformatted to FAT32 for these approx 3 min films with no issue

TLDR - M2025 needs D?

 

[Boojakascha]

Posting a new Type D build for anyone who wants to try it. Same base as the last one, two main changes:

• Manual white balance. While recording, use the arrows to pick R/G/B and +/- to adjust (±16 coarse, left/right for ±1 fine). The setting is saved and restored automatically after a power cycle. Use RST to reset back default values.
• Card-stall now stops the reel. If the SD card can't keep up and the recording stalls, you still get the on-screen CARD SLOW / REC STALLED warning — and now the motor also stops, leaving the frame counter frozen on the last good frame so you can see exactly where it cut out instead of finding out at the end.

Also cleaned up a false "REC STALLED" that used to flash in preview after a normal stop.

Reminder: for the higher bitrate, use a FAT32 card, 32 GB or smaller, Class 10 / V10+. Big exFAT cards write too slowly and will truncate long reels.

Thank you very much!

I confirm that it's working great on my Hardware Version D.

Fat32 formated Kingston 16 GB card, class 10.

The OSD flickers a tad now and then, but it's not bad at all. The glitches in the OSD are independent on whether I record or not. The recordings turn out very good.

 

[john-in-laguna]

Did you end up trying out the D version? Just ordered a unit off Amazon, similar serial number: J2925148BK01099. From what I can tell it's probably a D but it hasn't been tested yet.

I purchased a unit on Amazon as well. It arrived on June 24th. After a first round of tests with 8mm and Super8mm film, I was disappointed with the results. Luckily, I came across this forum and joined. My serial number is J2925148BK00441. There are postings that indicate that the firmware "type" of this unit is unclear. It may be D... it may be something even newer. I took the plunge and loaded the version D WIP version. The results are mixed. Yes, the scans are now 1600x1200, 18fps, and a bitrate of about 32K. They look much better than with the stock firmware. All the stock button functions continue to work as before. There is much discussion about changing the settings during recording. The settings in the lower right of the screen should display a [] around them when they are the target of the setting change. This is said to be changed with the arrow keys. This does not occur on my unit using the D WIP firmware. Maybe others can chime in as well.

 

[Boojakascha]

I purchased a unit on Amazon as well. It arrived on June 24th. After a first round of tests with 8mm and Super8mm film, I was disappointed with the results. Luckily, I came across this forum and joined. My serial number is J2925148BK00441. There are postings that indicate that the firmware "type" of this unit is unclear. It may be D... it may be something even newer. I took the plunge and loaded the version D WIP version. The results are mixed. Yes, the scans are now 1600x1200, 18fps, and a bitrate of about 32K. They look much better than with the stock firmware. All the stock button functions continue to work as before. There is much discussion about changing the settings during recording. The settings in the lower right of the screen should display a [] around them when they are the target of the setting change. This is said to be changed with the arrow keys. This does not occur on my unit using the D WIP firmware. Maybe others can chime in as well.

I think stock D's just record super 8 at 840x624 and artificially blow it up to a higher resolution for the sharpening processing.

You would want to lower the stock lens down or change the lens for 0dan0's one to yield sharpness beyond that initial resolution.

 

[ArgieBargie]

Hi ArgieBargie,

I hope your film scanning is going well. I just wanted to follow up regarding the original firmware dump from your A3026 unit.
My return window is now getting quite close, so I need to decide soon whether to return my scanner or attempt another recovery method.
Have you had a chance to extract the firmware yet, or do you have an approximate idea of when you might be able to do it?
I completely understand that you need to finish your family films first, and I do not want to pressure you. I just need to know whether the dump is likely to be available before my return deadline.
Thank you again for offering to share it.

I'm down to the last few reels. Sorry that I haven't gotten them done quicker, and what I thought was the last few of them turned out to be several large reels.


I'm itching to get this first pass done, because I'm getting plenty of the stupid flickering problems that plague these devices. I haven't forgotten about your plight, either. I'd say never mind the return deadline, because even if I get the stock firmware off this in the near future, you'll probably want to stick around until the clever folks here can finagle it. I have been doing at least one large reel each night, and I have about 4 more to go. This is on my mind each time I chuck a new reel on.


EDIT:
Also, I have a USB to TTL serial. I don't think I have an arduino handy. I have a couple of different types, including the CH340 and I can use a terminal. I might as well start preparing to retrieve the dump once I get this thing apart.

 

[john-in-laguna]

My serial number is J2925148BK01666. I flashed FWDV280-2 (after removing the "-2") without any issues. Seems these new numbers are D's.

Now I need to figure out how to changes the values...

Thanks , melw!

Hello Mike, I have a similar serial number (J2925148BK00441) and am using the latest D WIP firmware from melw and it is a definite improvement! I also am having difficulty figuring out how to change the configuration settings. For example, the FPS is set to 18. I would like to change it to 16 for some regular 8mm film. Pressing the arrow keys during recording is not moving the []. Maybe our hardware is slightly different?

 

[melw]

Another Type D test build. What's new since the previous build:

• Selectable frame rate (16 / 18 fps). Toggle it in the recording menu.
• Date-setting. Set the recording date (YYYY-MM-DD). Works for 1980–2100 (per FAT32 filesystem limit)

Using the menu (while recording): press Up/Down to move between settings — FPS, White Balance R/G/B, RST, Date Y/M/D. Use +/- to change the selected one (left/right gives fine steps on white balance). RST resets everything back to defaults. All settings persist across power cycles.

Tweaked the encoder's Qp parameter value floor to 20. Should help with rare freezes that can happen on grainy footage

 

[john-in-laguna]

Hello Mike, I have a similar serial number (J2925148BK00441) and am using the latest D WIP firmware from melw and it is a definite improvement! I also am having difficulty figuring out how to change the configuration settings. For example, the FPS is set to 18. I would like to change it to 16 for some regular 8mm film. Pressing the arrow keys during recording is not moving the []. Maybe our hardware is slightly different?

Hello again, Mike... I was confused about how to change the settings in recording mode. I was expecting the [] to move to the setting to be changed. That is incorrect. After some interaction with melw, I now understand that while recording, the sel:[] display shows the target parameter. Pressing the up/down keys will cycle the targeted parameter. Then pressing the +/- keys will adjust that parameter. For example, when the UI shows sel:[FPS], the +/- keys will toggle between the values of 16fps and 18fps. Now that I understand this, life is good!

 

[ArgieBargie]

I can't wait to try out this upgraded mode, if that's even possible with my weirdo version.